Welcome to the TalkTalk TV remote control guide. There are several versions of the TalkTalk remote, so please make sure you match your remote to the correct information below.
When you start watching a live TV channel you’ll be able to pause, rewind and fast forward thanks to temporary content stored on your TV Box.
We call delayed TV. Your TV Box only stores content on the channel you're watching from the point you started watching it. And when you change the channel, the temporary storage on your TV Box is wiped.
The storage limit varies depending on which Box you have. For the TalkTalk TV Plus Box it's about 2 hours and for the TalkTalk TV Box it's about 30 minutes. Content storage can also vary when it comes to HD.
Find out more about the features and controls using the table below:
Skip back to a previous point on the channel you're viewing. This takes you into delayed TV.
Pause live TV
Skip through the stored content up to the point of real-time TV. Check the time bar at the bottom of the screen for the fast forward limit.
Play live TV at any point
Exit delayed TV and return to live. A warning will remind you that all stored content for this channel will be deleted.
On Demand uses all the features above, without the limitations of the temporarily stored content. That means you can skip, fast-forward, pause and rewind as much as you like. You can also watch programmes more than once, as long as they're available.
Before you start, turn the volume of your TalkTalk TV Box up to a high setting using your TalkTalk remote. This will ensure that the sound isn't too quiet after pairing.
Remote V1 & 2: Press and hold Search on your remote until flashes green 3 times and remains lit.
Remote V3: Press and hold the Search button on your remote for at least 3 seconds until the red LED blinks 3 times and stays lit, then release the Search button.
Remote V1 & 2: Press and hold down the number button that corresponds with your TV manufacturer from the list below (if your TV manufacturer isn’t in this top 10 then please use the search box further down, where you will find more).
Remote V3: Press and hold down the number button that corresponds with your TV manufacturer from the list below (If your TV manufacturer isn't in this top 10 then please follow the separate steps below where you'll need to use the search box further down to locate your code).
Remote V1 & 2: Your TV will turn off. When it does, release the number button immediately to make sure the right code is applied. will now flash twice on your remote confirming the setting.
Remote V3: Your TV will turn off. When it does, release the number button immediately to make sure the right manufacturer code is applied. Once the red LED flashes twice, switch your TV on again.
You'll now be able to control your TV using your TalkTalk remote.
|Digit top 10 brands|
|1. Grundig||6. Samsung|
|2. JVC||7. Sharp|
|3. LG||8. Sony|
|4. Panasonic||9. Thomson|
|5. Philips||0. Toshiba|
If your TV manufacturer isn’t listed, follow our steps below and use the search box to find your 4 digit code. We recommend working from the left (the most popular codes) trying each one until you find the right one.
On your TalkTalk TV remote control press and hold OK and the top right button Power button on your TalkTalk remote until TalkTalk flashes twice
Enter the 4 digit code from the table using the number buttons on your remote (find your code in the table below)
Depending on whether or not the correct code has been entered, one of the following will happen: If the correct code has been entered 'TalkTalk' will flash green twice. If an invalid code has been entered 'TalkTalk' will give one long flash
On your TalkTalk TV remote control press and hold digit 1 and digit 6 simultaneously for 3 seconds. After 3 seconds, the red LED will light up and stay lit.
Enter the 4 digit code from the table using the number buttons on your remote (find your code in the table below).
Depending on whether or not the correct code has been entered, one of the following will happen: Correct code: The red LED will blink twice and return to use mode. You should now be able to control your TV using your TalkTalk TV remote. Invalid code: The red LED will blink rapidly 5 times and return to use mode. Start the steps again to try a different code.
Keep trying the codes listed next to your TV’s manufacturer, working from the left (these are the most popular) until you find the correct one. You'll need to repeat all the steps above each time you try a new code.
Our experts are here to help, select one of the following contact options:
View your bills, keep tabs on your usage and message our team.
Manage your boosts and check the status of your service.
To help us deal with your query quickly, please confirm the following information when you write to us. We will aim to respond in writing to your query in 10 days.
- Your full name
- Your TalkTalk Phone or mobile number
- Your Signature
TalkTalk Correspondence Dept
PO Box 675
All letters will be sent to the primary billing address unless stated otherwise. Please also include the best way to contact you about your query, such as your contact phone number or contact address.
Call us for free on: 0345 172 0088
Make sure you have your account details to hand when you call.
Calls are free from your TalkTalk phone, our customer services team are available 8am-8pm, Technical Support 24/7 every day.
If you’re deaf, hard of hearing or speech-impaired, the Text Relay Service can be used to help you contact us, simply dial 18001 followed by 0345 1720088