TalkTalk TV box problem.

[jimbly]

I have been in contact via live chat this morning about my TalkTalk tv box problem, which is, I can only get the "no signal" floating graphic on the tv screen. I have tried turning off the box and then back on again, it goes through the set up, but then just to the no signal graphic again. It does not respond to the handset. I have plugged the aerial directly into the TV and there is no problem with the programmes at all.

I have had two attempts at the live chat, the first I got quite a way through with the agent who was going to do some checks on the line to my property and then the chat was disconnected, I tried again and got through to the second agent and only managed to give him my details and the fault, but the chat was disconnected again.

As the aerial signal is not the problem I can only assume that the box is faulty and if so, how do I get a replacement.

Anyone can help please??

[jimbly]

Thanks for that Karl, when it let's me get into settings, I will try that and see if it's any better.

Cheers.

Jimbly

[Karl-TalkTalk]

Hi

It is possible the box is starting to fail.  You can try a full factory reset from the settings menu and see if that changes anything, but if not, then the box will have failed.

As we do not provide these box models any more, then it cannot be repaired or replaced.

You may be eligible for one of the new 4K TV boxes.

Thanks  

Karl. 

[jimbly]

Hello Karl, it's gone from bad to unusable now. Can't see any channels now, it's either saying no signal with a black screen or very occasionally a few coloured pixels.  So I can't watch live TV and it continually fails to record because of this.  With the aerial connected direct to the TV there is no problem with the reception at all.

Is the box faulty/breaking down?

Any help please.

Cheers.

[Karl-TalkTalk]

Ok, Thanks for letting me know.

Karl.

[jimbly]

Checked tht Karl, but it still works the same as it did with it switched off.  No signal on tv when switched to aerial input.

Which isn't a problem, if I get a box problem I'll just switch the aerial cable to tv direct.

Thanks.

[Karl-TalkTalk]

Hi

The antenna out function will allow the aerial signal to pass through to you TV so you can use the TV freview option with the aerial signal.

If the no signal message appears on screen, first thing to check is that the HDMI cable is seated correctly, the correct HDMI (source) channel has been selected, and see if you can see any youview menus when pressing any keys on the remote.

Karl.

[jimbly]

Right I've done that.  What is the function of this.

Just to say, that the box would not get past the no signal screen at all yesterday, despite trying numerous times between 8am and 11pm, but this morning the came on as normal and so far is working normally.

[Karl-TalkTalk]

Hi

OK, first question, when you select the correct source channel on your TV, do you see the youview menu when pressing the remote ?

To locate the Antenna Out, go to Settings, then picture and quality, and Antenna Out should be the bottom option.

Karl.

[KeithFrench]

YouView > Settings > Picture & Sound > Antenna out

Turn this on.

[jimbly]

Found it!

DN372T.01.03.P

[jimbly]

Hello,

Where do i find the model number?

Cheers.

[Karl-TalkTalk]

Hi

what model box do you have ?

Karl.

[jimbly]

Hello Karl,  Thanks for the reply.  I have looked but I can't see where the aerial out setting is.  That said, no changes have been made to the box settings.

Cheers.

Jimbly

[Karl-TalkTalk]

Hi Jimbly,

Did you follow the advice from Keith and enable Aerial out in the settings ?

Thanks  

Karl. 

[KeithFrench]

Is this only when the TV box is in standby mode & OK when it is turned on? If that is the case have you enabled the aerial out option in settings?

Which TV box model number do you have?